Digital Microscope Keyence VHX7000: Difference between revisions
Jump to navigation
Jump to search
| Line 19: | Line 19: | ||
[[Image:Mask-Aligner_Suss-MicroTec-MA6.jpg|thumb|upright=1.12|Suss MicroTec model MA6 Mask Aligner (model MA6/BA6 is shown at the top of the infobox)]] | [[Image:Mask-Aligner_Suss-MicroTec-MA6.jpg|thumb|upright=1.12|Suss MicroTec model MA6 Mask Aligner (model MA6/BA6 is shown at the top of the infobox)]] | ||
The contact mask aligner is a tool that enables front- and back-side alignment of photo masks to create structures as small as 500 nm on sample sizes up to 6 inches. These systems are ideally suited for rapid definition of sub-micron devices through contact printing, and enable the high-resolution alignment of several lithographic layers to define complex devices. They are typically used to define contacts and connections to the nanostructures that are defined using the KNI's other fabrication instruments (e.g. e-beam lithography). The MA6/BA6 is also configured to do bond aligning in support of the Suss Microtec SB6L Wafer Bonder. | The contact mask aligner is a tool that enables front- and back-side alignment of photo masks to create structures as small as 500 nm on sample sizes up to 6 inches. These systems are ideally suited for rapid definition of sub-micron devices through contact printing, and enable the high-resolution alignment of several lithographic layers to define complex devices. They are typically used to define contacts and connections to the nanostructures that are defined using the KNI's other fabrication instruments (e.g. e-beam lithography). The MA6/BA6 is also configured to do bond aligning in support of the Suss Microtec SB6L Wafer Bonder. | ||
==== | ==== Objectives Available ==== | ||
* | * Low Magnification Lens = 20-100x | ||
* | * Medium Magnification Lens = 100-500x | ||
* | * High Magnification Lens = 500-2500x | ||
* Highest Magnification Lens = 2500-6000x | |||
==== Suss2 MA6 Applications ==== | ==== Suss2 MA6 Applications ==== | ||
Revision as of 20:09, 14 December 2023
|
Description
The contact mask aligner is a tool that enables front- and back-side alignment of photo masks to create structures as small as 500 nm on sample sizes up to 6 inches. These systems are ideally suited for rapid definition of sub-micron devices through contact printing, and enable the high-resolution alignment of several lithographic layers to define complex devices. They are typically used to define contacts and connections to the nanostructures that are defined using the KNI's other fabrication instruments (e.g. e-beam lithography). The MA6/BA6 is also configured to do bond aligning in support of the Suss Microtec SB6L Wafer Bonder.
Objectives Available
- Low Magnification Lens = 20-100x
- Medium Magnification Lens = 100-500x
- High Magnification Lens = 500-2500x
- Highest Magnification Lens = 2500-6000x
Suss2 MA6 Applications
- Front Side Alignment & Exposure
- Back Side Alignment with Front Side Exposure
Resources
Manufacturer Specifications
- Whole wafers 2” up to 6” can be loaded.
- Samples pieces up to 6”x6” square can be loaded.
- Samples up to 6mm thick can be loaded..
- Exposure Resolution:
- Soft Contact Mode = 1 - 2 um
- Hard Contact Mode = 1 um
- Soft Vacuum Contact Mode = 1 - 0.5 um
- Vacuum Contact Mode = 0.4 - 0.5 um
Suss 1 Exposure Settings
- Channel 1 is 365nm wavelength at 15 mW/cm2.
- Channel 2 is 405nm wavelength at 25 mW/cm2.
Suss 2 Exposure Settings
- Channel 1 is 365nm wavelength at 10 mW/cm2.
- Channel 2 is 405nm wavelength at 15 mW/cm2.
SOPs & Troubleshooting
- General SOP & Troubleshooting
- Lamp Change SOP
- Lamp Re-Ignition SOP
- Suss 1 Lamp Re-Ignition Video
- Suss 2 Lamp Re-Ignition Video
Manufacturer Manuals
- Suss MA6/BA6 System Manual
- Suss MA6/BA6 Brochure
- Lamp Power Supply Manual
- Alignment Mark Suggestion Document
Labrunr Reservation Rules:
| Advanced Res (days) | Limit per Res (hrs) | Limit per week (hrs) | |
|---|---|---|---|
| Weekday | 7 | 4 | 12 |
| Weeknight | 7 | 6 | 18 |
| Weekend | 14 | 6 | 18 |
For reservations that DO NOT follow the reservation policy, email the tool manager BEFORE scheduling. Your reservation can be cancelled at any time by the tool manager if it does not follow the tool reservation policy.
Equipment Status
- LabRunr Equipment Status (Select Suss1 or Suss2 from the dropdown menu)
Optical Lithography Resources
- Optical Lithography Resources Page
- Laurell Spinner Cleaning SOP
- Laurell Spinner - Spinning Resist Video
Process Recipes